billhook301
Básico
Primeiro-sargento marítimo · 279 pts
Knebworth, Hertfordshire, United Kingdom
Membro desde Abr 2019
Último online há 4 anos
Idade 80
Assinatura
Sky Diving, if at first you don't succeed, give up.
billhook301’s porto
5 barcosSpringer Tug
Scratch built tug with bits leftover from my Puffer build
clyde puffer
scratch built puffer getting there
My Swordsman
First run in 15/20 years not to bad
Mk1 Micro Magic
Been gathering dust, time to go sailing!!!!!!!!!!
Old Swordsman or Huntsman ?
Purchased many moons ago in a sorry state, the wiring was a bit of rats nest, I tided it up and and ran it …
billhook301’s blogs de construção
3 blogsFreelance design for 3D printed tug,all stl files created by PeterSripol here is a link to his channel on YouTube. https://www.youtube.co…
I have an old drone I no longer use so I thought I would try and use the camera without the motors and body to make my own wi-fi camera f…
Building this tug with wood left over from my Clyde Puffer, more info as I go along. Building to Springer spec 18 inch's long 8 inch's wide.
Seguidores
3 seguidorsEnvios recentes
Última atividade
Última publicação há 6 anos
+5♥ 9 likes1,065 viewsRe: 3D Printed Tug.Yes you can print ABS but a much higher temp. also you need some means of venting off the fumes, you have not got that problem with PLA. See this guide filaments- https://all3dp.com/1/3d-printer-filament-types…♥ 2 likes1,060 viewsRe: 3D Printed Tug.1) Printer- Anet a8 cheap and cheerful 2) All my printing is done with PLA, there are many types of filament available but PLA seems the most popular. 3) With this printer you can print anything that fits in a…♥ 2 likes1,058 views3D Printed Tug.Being a tight a** I have printed two UV joint's for the Tug OK for low power use but no good for IC, also the main winch. UV joint drilled for M4 prop shaft and 2.3 mm motor shaft with two M4 Allen Socket Hex …
+4♥ 9 likes1,060 viewsRe: 3D Printed Tug.Hi Martin, lets say it's not as easy as sanding wood, I wont be doing it again but I am to far in to stop now, just did it to see if it could be done. Much prefer wood but will still print small detail parts f…♥ 1 like1,057 views3D Printed Tug.A bit more done on my Tug, the only part that is wood is the deck. Waiting for prop shaft's and coupling's. Have sealed the hull with two coat's Z-Poxy
+5♥ 9 likes1,058 viewsRe: 3D Printed Tug.That's how they came off the printer, just removed the brim♥ 1 like1,057 views3D Printed Tug.Freelance design for 3D printed tug,all stl files created by PeterSripol here is a link to his channel on YouTube. https://www.youtube.com/watch?v=QaIjdgTiP0o&list=WL&index=2&t=734s My version will be printed …
+4♥ 9 likes4 comments1,057 viewsRe: Springer WI-FI DIY CameraHi Marky, yes indeed I did👍♥ 2 likes660 viewsRe: Springer WI-FI DIY CameraHi Martin, already on it👍👍👍👍♥ 2 likes659 views